|
|
|
|
SG-Link® Wireless Strain Node
Direct strain gauge input datalogging transceiver for use in high speed wireless
sensor networks.
Features and Benefits
- 2.4 GHz direct sequence spread spectrum radio is license free worldwide
- IEEE 802.15.4 open communication architecture
- supports simultaneous streaming from multiple nodes to PC
- datalogging rates up to 2048 Hz
- real-time streaming rates up to 4 KHz
- on-board memory stores up to 1,000,000 measurements
- communication range up to 70m line-of-sight, 300m with high gain antennas
- regulated 3 volt sensor excitation supports most analog sensors
- on-board bridge completion resistors
- includes internal resistor for wireless shunt calibration
- low power consumption for extended use
-
internal rechargeable battery
|
|
|
|
Description
With one differential channel, which includes full strain gauge
conditioning and programmable off set, and one single ended
channel, the SG-LINK® is compatible with most types of analog
sensor. Fast and extremely versatile, the SG-Link® is designed to
operate as part of a high speed wireless sensor network.
Featuring 2 KHz sweep rates, combined with 2 Mbytes flash
memory, these little nodes pack a lot of power in a small
package. With every node in the wireless network assigned a
unique 16 bit address, a single host transceiver can address
thousands of multi-channel sensor clusters.
The bi-directional RF communications link can trigger
to be logged from 70 meters, or request real-time data
be transmitted to the host PC for data acquisition/analysis.
The frequency agile system enables simultaneous real-
streaming from up to 16 nodes in the 2.4 GHz range.
The scaleable system architecture and programmable sensor
interface enables a new generation of wireless sensor networks.
The SG-LINK® is compatible with a wide range of wheatstone
bridge type sensors, including strain gauges, displacement
sensors, load cells, torque transducers, pressure sensors,
accelerometers, geophones, temperature sensors, inclinometers,
and others.
A Software Development Kit is available, which includes
fully-commented source code and a compiled executable
for: Microsoft® C++ 6.0, Microsoft® Visual Studio C++ .NET 7.1,
Microsoft® VB 6.0, Microsoft® VB.NET 2003, Microsoft® VB.NET
2005 and LabVIEW® 7.1.
June 3, 2007
|
Applications
Condition-based monitoring of machines
Health monitoring of civil structures and vehicles
Smart structures and materials
Experimental test and measurement
Robotics and machine automation
Vibration and acoustic noise testing
Sports performance and sports medicine analysis
Distributed security networks
|
|
Input Channels |
1 full differential input channel, 350Ω resistance or higher (with optional
bridge completion), 1 single ended input (0 - 3 volts maximum), and internal temperature
sensor |
|
Temperature Sensor |
-25˚C to 70˚C range, accuracy ± 4˚C |
|
Measurement Accuracy |
± 0.1% typical |
|
Resolution |
± 1 bit 0.0024%
± 1 microstrain typical for 3 wire quarter bridge strain gauge |
|
DC Bridge Excitation |
+3 volts DC at 50 mA maximum (pulsed to sensors for samples rates of 100 Hz and below to conserve power) |
|
Programmable Gain |
Software programmable: 2 to 1831 |
|
Programmable Offset |
Software programmable |
|
Analog to Digital (A/D) Converter |
Successive approximation type, 12 bit resolution
|
|
Data Storage Capacity |
2 megabytes (approximately 1,000,000 data points) |
|
Data Logging Mode |
Log up to 1,000,000 data points (from 100 to 65,500 samples or continuous) at 32
Hz to 2048 Hz |
|
Sensor event driven trigger |
Commence datalogging when threshold exceeded |
|
Real-time streaming mode |
Transmit real time data from node to PC - rate depends on number of active channels:
1 channel - 4 KHz, 2 channels - 2 KHz, 3 channels - 1.33 KHz |
|
Low duty-cycle mode |
Supports multiple nodes on single RF channel, total update bandwidth of 500 Hz divided
by number of nodes |
|
Synchronization between nodes |
Datalogging 100 µsec ± 50 ppm. LDC mode time stamped at PC |
|
Sample rate stability |
Datalogging and LDC (mode(2Hz to 500Hz) 100 µsec ±
25 ppm (90 msec/hour) LDC mode (1 Hz to 2 samples per
hour) ± 10% |
|
Wireless shunt calibration |
Channel 1. Internal shunt calibration resistor 499 KΩ |
|
Radio Frequency (RF) Transceiver Carrier |
2.4 GHz direct sequence spread spectrum, license free worldwide (2.450 to 2.490
GHz) - 16 channels |
|
RF Data Packet Standard |
IEEE 802.15.4, open communication architecture |
|
RF Programming & Downloading |
8 minutes to download full memory |
|
Range for Bi-directional RF Link |
70 m line-of-sight, up to 300 m with optional high gain antenna |
|
Internal Li-Ion Battery |
3.7 volt lithium ion rechargeable battery, 200 mAh capacity. Customer may supply
external power from 3.2 to 9 volts |
|
Power Consumption |
SG-Link node only: real-time streaming - 25 mA, datalogging - 25 mA, sleeping -
0.5 mA External sensors: 350 Ω strain gauge - 8 mA, 1000 Ω strain gauge
- 3 mA (add sensor consumption to above to calculate total power consumption) |
|
Operating Temperature |
-20 to +60˚C with standard internal battery and enclosure, extended temperature
range optional with custom battery and enclosure. -40 to +85˚C for electronics
only |
|
Dimensions* |
58 mm x 49 mm x 26 mm without antenna (board only 47 mm x 36 mm x 24 mm) |
|
Weight |
46 grams |
|
Case |
ABS plastic |
|
Software |
Agile-Link™ Windows XP® compatible |
|
PC Comm |
Serial port, 115.2 kBaud |
*For dimensioned print go to www.microstrain.com
|
|
General Documentation
Mechanical Prints
Technical Notes
FAQ's
|
Please enter your Contact information.
When finished, click SUBMIT button at bottom of page.
To better serve your needs, the fields marked * indicate required information.
SG-Link® Starter Kits
|
 |
SG-Link 1 input channel, USB base station starter kit
SG-LINK-1CH-2400-SK2
Includes
(2) SG-Link-1CH-2400-M, (1) USB base station, (1) USB cable, (1) SG-Link power supply, (3) antennae, Windows XP compatible software
Part Number: 6308-0042
Online price: $2095.00
|
MicroStrain has identified your location as
United States. If this is incorrect please contact
sales at 802-862-6629 or sales@microstrain.com
|
 |
SG-Link 1 input channel, Analog output base station starter kit
SG-LINK-1CH-2400-SKA
Includes
(1) SG-Link-1CH-2400-M, (1) Analog output base station, (1) SG-Link power supply, (1) Analog base station power supply, (2) antennae, Windows XP compatible software
Part Number: 6308-0011
Online price: $2145.00
|
MicroStrain has identified your location as
United States. If this is incorrect please contact
sales at 802-862-6629 or sales@microstrain.com
|
|
|
|
